Sled Pulling Rules
2026 Open House Sled Pulling Rules
Description
Stock Diesel
1, Weight limit- 8,500lb, no external weights forward of the front bumper
2, Dot legal tires, 35” x 12.5 maximum. No dual tire setups unless vehicle came factory with duals.
3, Upward or downward facing exhaust preferred. No hood/fender exit exhausts.
4, No power adders- nitrous, propane assist, water meth injection.
5, Tuning and tuners are allowed.
6, Turbo- Factory unaltered turbocharger.
7, Receiver style hitch, 26” hitch height, hook point no closer to the center line of the rear axle than 44”- suspension stops and traction bars allowed.
2.5
1, Weight limit- 8,500lb, no external weights forward of the front bumper
2, Dot legal tires, 35” x 12.5 maximum. No dual tire setups unless vehicle came factory with duals.
3, Upward or downward facing exhaust, no hood/fender exit exhausts.
4, Safety- (HELMET REQUIRED) 2 Rear drive shaft hoops, kill switch at the rear of the vehicle recommended.
5, Duel fueler/ twin injection pump setups allowed - No power adders- nitrous, propane assist, water meth injection.
6, Turbos- stock appearing factory style turbos must not exceed 2.5" inducer wheel .
7, Receiver style hitch, 26” hitch height, hook point no closer to the center line of the rear axle than 44”- suspension stops and traction bars allowed.
Workstock
1, Weight limit- 8,500lb, no external weights forward of the front bumper
2, Dot legal tires, 35” x 12.5 maximum. No dual tire setups unless vehicle came factory with duals.
3, Upward or downward facing exhaust, no hood/fender exit exhausts.
4, Safety- (HELMET REQUIRED) 2 Rear drive shaft hoops, kill switch at the rear of the vehicle recommended.
5, Duel fueler/ twin injection pump setups allowed - No power adders- nitrous, propane assist, water meth injection.
6, Turbos- stock appearing factory style turbos, s300 frame turbos may run up to 69mm inducer wheel, s400 frame turbos must not exceed 64.5mm (2.5”) inducer wheel .
7, Receiver style hitch, 26” hitch height, hook point no closer to the center line of the rear axle than 44”- suspension stops and traction bars allowed.
3.0 Will strictly follow the 3.0 PPL rules:
1, Turbocharger Rules: Maximum 3.0-inch (76.2mm) inducer bore on the compressor housing. The compressor wheel must protrude at least 1/8 inch into the 3.0-inch bore. Map Width Enhancement (MWE) groove is permitted but must be within the 3.0-inch neck area.
2, Safety Requirements: A 3/8-inch billet steel cross must be installed in the inlet of the turbo within 8 inches of the compressor wheel. Turbo pressure pipe must be either 0.120-inch thick steel or covered with a 5-layer Kevlar blanket.
3, Hitch & Suspension: Hitch height is 26 inches with a 3.75-inch or larger hole. Rear suspension must be locked solid.
Hot Street
1, Weight limit- 8,500lb. Hanging weight allowed. No weight boxes.
2, Dot legal tires, 35” x 12.5 maximum.
3, Upward facing exhaust required. Cross bolts or billet cross in exhaust at turbo outlet required.
4, Safety- (HELMET and Fire Jacket REQUIRED) front and rear drive shaft hoops, U joint shields, kill switch at the rear of the vehicle required.
5, Turbos- Any single or compound turbo setup allowed.
6, Receiver style hitch, 26” hitch height, hook point no closer to the center line of the rear axle than 44”- suspension stops and traction bars allowed.
ALL TRUCKS IN STOCK, 2.5, WORKSTOCK, AND HOTSTREET MUST RETAIN A 1 TON OR SMALLER CHASIS.
ALL ENGINES MUST BE A FACTORY ENGINE OPTION FROM A 1 TON OR SMALLER TRUCK
RWYB
1, 8000Lbs
ALL RULES ARE TENTATIVE AND SUBJECT TO CHANGE AS THE EVENT DRAWS NEAR
1, Weight limit- 8,500lb, no external weights forward of the front bumper
2, Dot legal tires, 35” x 12.5 maximum. No dual tire setups unless vehicle came factory with duals.
3, Upward or downward facing exhaust preferred. No hood/fender exit exhausts.
4, No power adders- nitrous, propane assist, water meth injection.
5, Tuning and tuners are allowed.
6, Turbo- Factory unaltered turbocharger.
7, Receiver style hitch, 26” hitch height, hook point no closer to the center line of the rear axle than 44”- suspension stops and traction bars allowed.
2.5
1, Weight limit- 8,500lb, no external weights forward of the front bumper
2, Dot legal tires, 35” x 12.5 maximum. No dual tire setups unless vehicle came factory with duals.
3, Upward or downward facing exhaust, no hood/fender exit exhausts.
4, Safety- (HELMET REQUIRED) 2 Rear drive shaft hoops, kill switch at the rear of the vehicle recommended.
5, Duel fueler/ twin injection pump setups allowed - No power adders- nitrous, propane assist, water meth injection.
6, Turbos- stock appearing factory style turbos must not exceed 2.5" inducer wheel .
7, Receiver style hitch, 26” hitch height, hook point no closer to the center line of the rear axle than 44”- suspension stops and traction bars allowed.
Workstock
1, Weight limit- 8,500lb, no external weights forward of the front bumper
2, Dot legal tires, 35” x 12.5 maximum. No dual tire setups unless vehicle came factory with duals.
3, Upward or downward facing exhaust, no hood/fender exit exhausts.
4, Safety- (HELMET REQUIRED) 2 Rear drive shaft hoops, kill switch at the rear of the vehicle recommended.
5, Duel fueler/ twin injection pump setups allowed - No power adders- nitrous, propane assist, water meth injection.
6, Turbos- stock appearing factory style turbos, s300 frame turbos may run up to 69mm inducer wheel, s400 frame turbos must not exceed 64.5mm (2.5”) inducer wheel .
7, Receiver style hitch, 26” hitch height, hook point no closer to the center line of the rear axle than 44”- suspension stops and traction bars allowed.
3.0 Will strictly follow the 3.0 PPL rules:
1, Turbocharger Rules: Maximum 3.0-inch (76.2mm) inducer bore on the compressor housing. The compressor wheel must protrude at least 1/8 inch into the 3.0-inch bore. Map Width Enhancement (MWE) groove is permitted but must be within the 3.0-inch neck area.
2, Safety Requirements: A 3/8-inch billet steel cross must be installed in the inlet of the turbo within 8 inches of the compressor wheel. Turbo pressure pipe must be either 0.120-inch thick steel or covered with a 5-layer Kevlar blanket.
3, Hitch & Suspension: Hitch height is 26 inches with a 3.75-inch or larger hole. Rear suspension must be locked solid.
Hot Street
1, Weight limit- 8,500lb. Hanging weight allowed. No weight boxes.
2, Dot legal tires, 35” x 12.5 maximum.
3, Upward facing exhaust required. Cross bolts or billet cross in exhaust at turbo outlet required.
4, Safety- (HELMET and Fire Jacket REQUIRED) front and rear drive shaft hoops, U joint shields, kill switch at the rear of the vehicle required.
5, Turbos- Any single or compound turbo setup allowed.
6, Receiver style hitch, 26” hitch height, hook point no closer to the center line of the rear axle than 44”- suspension stops and traction bars allowed.
ALL TRUCKS IN STOCK, 2.5, WORKSTOCK, AND HOTSTREET MUST RETAIN A 1 TON OR SMALLER CHASIS.
ALL ENGINES MUST BE A FACTORY ENGINE OPTION FROM A 1 TON OR SMALLER TRUCK
RWYB
1, 8000Lbs
ALL RULES ARE TENTATIVE AND SUBJECT TO CHANGE AS THE EVENT DRAWS NEAR
Shipping Information
- Item Requires Shipping